Program New Sensor / Learn New Sensor

Note: Videos will be attached at the bottom

There are 2 ways of entering programming of sensors, however option 1 is much simpler and is better for those who are new to programming security panels.

Option # 1 - Advanced Programming (Easiest Mode)

1) Enter Installer Code (Default 4112) + 800

2) Once you see 20 Installer Code, Press "OFF"

3) Press ↓ and then Aux/Select

Selecting Sensor Type:

4) Use the arrow keys to select the sensor type of the sensor

- press AUX/SELECT when complete

4.1) Panel May ask to select location, use arrow keys to find desired name and then press AUX/SELECT when complete

Learn Mode:

5) Panel is now in learn mode, follow voice instructions to add sensor

6) When Panel has learned sensor, select AWAY/ADD to add the sensor or press OFF/ESCAPE to cancel.

**Option # 2 - *56 Enhanced Programming**

1) Enter Installer Code (Default 4112) + 800

2) When you see 20 Installer Code, press *56

3) You will be prompted for a zone number

Guide:

00 - Exit Zone Programming

01 - Hard Wired Zone

02-25- RF Zones Only

26-41 - Button Zones (only)

92 - Duress

95,96,99 - Panic Zones

- Press * to continue

4) You will now see b00 NOT USED ZONE TYPE Enter your zone type

- press # to go back if you would like to go back

- Each Zone has 2 digit zone types

Guide:

00 - Not Used, you will be asked to delete sensor if this is selected

01 - Entry/Exit # 1

02 - Entry/Exit # 2

03 - Perimeter

04 - Interior Follower

05 - Trouble Day/Alarm Night

06 - 24 Hr Silent

07 - 24 Hr Audible

08 - 24 Hr Aux

09 - Fire Without Verification

10 - Interior w/Delay

14 - Carbon Monoxide

16 - Fire With Verification

20 - Arm-Stay

21 - Arm-Away

22- Disarm

23 - No Alarm Response

24 - Silent Burglary

- Press * to continue after inputting a zone type

5) You will now see a C00 Report Code, if you have changed reporting type follow the report code guide otherwise enter 0100

- Press * to continue

6) You will now see d 3 RF SUPERVISED INPUT TYPE follow the guide bellow

3 = RF (supervised RF) – sends periodic check-in signals, faults, restore and low battery

signals

4 = UR (unsupervised RF) – sends same as “RF” type, but control does not supervise the

check-in signals

5 = BR (button type) – sends only fault and low battery signals; does not send restores or

check-in signals

- RF type transmitters must remain within range of the receiver, otherwise a

supervision failure signal will occur.

- UR and BR type transmitters may be carried off premises (out of range without

causing a supervision failure.

- Zones 2-25 should be assigned Input Type 3 or 4. Zones 26-41 should be

assigned Input Type 5 only.

- Press * to continue

7) you will now see E1 LOOP#/AUTO LEARN

Auto Learn- Here you can trigger your sensor to auto learn it into the system, make sure the sensor is not too close to the panel as that can cause issues

Manual Entry - Enter the desired loop number and press [✻] to continue ( Look at your sensor types guide for the loop number).

Guide:

1-4 = loop number for the zone of the transmitter being entered.

Note:LOOP NUMBER WILL BE FOUND IN SENSOR MANUAL

0 + [✻] = continue to DELETE ZONE PARAMETERS CONFIRMATION prompt (F)

[✻] = continue to the ENROLL MODE prompt (1A) if not entered, or VOICE DESCRIPTOR

prompt if already entered

[#] = return to previous prompt

Note: We recommend auto learning when possible, if auto learn does not work follow the sensor manual to enter the loop number.

- Press * when you you are ready

7.1) You will now see 1A ENROLL MODE If Auto Learn did not work

- if you see 1A L than this zone is already in use, if you want to delete this serial number press 9 + 1 and it will clear the serial number of the existing sensor

Guide:

0 = advance to the VOICE DESCRIPTOR prompt (1C) and save all zone parameters.

1 = enter now and proceed to SERIAL NUMBER prompt (1b).

2 = copy the last serial number entered into local ram.

9 = advance to F; delete existing serial number.

[✻] = advance to the VOICE DESCRIPTOR prompt (1C). This will save all zone parameters.

[#] = return to the LOOP NUMBER prompt (E).

8) You will now see 1C ZONE DESCRIPTOR

0 - Skip to Next Zone

1- Enter Descriptor Mode

9) You can now change the zone description, there are up to 3 descriptions per zone

- Enter # + 2 digit vocabulary Index

- 6 - Advance to next descriptor

- 8 Accept Word and Advance To Next Zone

`vocabulary Index`

82 ALARM

32 ATTIC

01 BABY

33 BACK

34 BASEMENT

35 BATHROOM

36 BEDROOM

83 CHECK

37 DELAY DOOR

38 DEN

02 DETECTOR

03 DINING

39 DINING ROOM

04 DOOR

40 DOWNSTAIRS

05 DRIVEWAY

06 EAST

41 EIGHT

42 EMERGENCY

43 FAMILY ROOM

87 FIRE

44 FIRE DETECTION

07 FIRST FLOOR

45 FIVE

08 FLOOR

46 FOUR

47 FRONT

48 GARAGE

49 GUEST ROOM

09 GUN

50 HALL

10 INSIDE

51 KITCHEN

11 LAUNDRY

52 LAUNDRY ROOM

12 LIBRARY

13 LIVING

53 LIVING ROOM

14 MAIN

15 MASTER

54 MASTER

BEDROOM

55 MEDICAL

84 MESSAGE

56 MOTION

DETECTOR

57 NINE

16 NORTH

58 NURSERY

59 OFFICE

60 ONE

17 OUTSIDE

61 PATIO

62 POLICE

18 POOL

63 REAR

19 ROOM

64 SECOND FLOOR

65 SEVEN

20 SHED

21 SHOP

66 SIDE

67 SILENT POLICE

68 SIX

69 SLIDING

22 SMOKE

23 SOUTH

24 STORAGE

85 SYSTEM

25 THIRD FLOOR

75 THREE

76 TRANSMITTER

77 TWO

78 UPSTAIRS

26 UTILITY

79 UTILITY ROOM

27 WEST

80 WINDOW

28 YARD

81 ZERO

86 ZONES

29 1st

30 2nd

31 3rd

70 Custom Word #1

71 Custom Word #2

72 Custom Word #3

73 Custom Word #4

74 Custom Word #5

99 Blank (for erasing a previously

programmed word)

Program Delay and Auto Learn Serial Number Contact:

https://www.youtube.com/watch?v=GXPsWyl7wQg&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=4

Note: You still need to program the sensor as a hard wired sensor

Program 5816 Contact:

https://www.youtube.com/watch?v=xtl6FyWfmaA&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=14

How to Program Instant:

https://www.youtube.com/watch?v=F8Tpyx_X8z4&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=16

Program 5818MNL Recessed Contact:

https://www.youtube.com/watch?v=9MSnWTsvqGA&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=18

5818MNL - How to Program Delay and Manually:

https://www.youtube.com/watch?v=1QOx0v9KBLs&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=20

5834-4 - How to Program Arm Away Button:

https://www.youtube.com/watch?v=2kvK6pyg_ck&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=36

5834-4 - How to Program the Disarm Button:

https://www.youtube.com/watch?v=jcfmous9DBY&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=37

5834-4 - How to Program the Arm Stay Button:

https://www.youtube.com/watch?v=x0LfuDe6f6w&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=38

5834-4 - How to Program with a Panic Button:

https://www.youtube.com/watch?v=Cwgc-IY1ecI&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=39

5853 - How to Program into the LYNX Plus:

https://www.youtube.com/watch?v=YkKk_SayClI&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=44

5800PIR-RES - How to Program Interior Follower L3000:

https://www.youtube.com/watch?v=Zve3AChQKF0&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=45

Change Zone Description:

https://www.youtube.com/watch?v=j0e1D93ePXs&list=PLGdtWAgjdwqGv_tUrH23U5VOJWJagU9qz&index=17