There will be videos attatched for most sensors below instructions

TO ENTER PROGRAMMING
1) Tap on the grey bar at the top middle of the screen

2) Tap Settings

3) Tap Advanced Settings

4) Enter either, Installer(Default 1111), Dealer (Default 2222)

5) Tap Installation

6) Tap Devices

7) Tap Security Sensors

8) Select Either "Add Sensor" or "Auto Learn Sensor"

Auto Learn Sensor:

1) Open the cover tamper for the device or press tamper button inside the sensor when needed

2) Sensor will be displayed on screen, confirm information and continue.

Add Sensor:

1) Fill out the information needed for the sensor that is currently being programmed in

Note: GeoArm recommends using "Auto Learn Sensor" as it is much friendlier to DIY installers

Enroll PG9914 Motion Detector:&nbsp;

<a href="https://www.youtube.com/watch?v=1rzgLozbTek" target="_blank">https://www.youtube.com/watch?v=1rzgLozbTek</a>

Enroll PG9945 Contact:

<a href="https://www.youtube.com/watch?v=lvunefTDk1Q" target="_blank">https://www.youtube.com/watch?v=lvunefTDk1Q</a>

Enroll PG9939 Key Fob:&nbsp;

<a href="https://www.youtube.com/watch?v=WF-86cNkS3I" target="_blank">https://www.youtube.com/watch?v=WF-86cNkS3I</a>

Enroll Power G Sensor:

<a href="https://www.youtube.com/watch?v=3yZSuLTg_D4" target="_blank">https://www.youtube.com/watch?v=3yZSuLTg_D4</a>

Enroll IQ Light Bulb:&nbsp;

<a href="https://www.youtube.com/watch?v=5qXwC06zesc" target="_blank">https://www.youtube.com/watch?v=5qXwC06zesc</a>

Enroll QS5110-840 Smoke Detector:&nbsp;

<a href="https://www.youtube.com/watch?v=AEZ-FM-DsK0" target="_blank">https://www.youtube.com/watch?v=AEZ-FM-DsK0</a>

Enroll IQ Carbon:

<a href="https://www.youtube.com/watch?v=omNLr-3p-9M" target="_blank">https://www.youtube.com/watch?v=omNLr-3p-9M</a>

There will be videos attatched for most sensors below instructions

TO ENTER PROGRAMMING
1) Tap on the grey bar at the top middle of the screen

2) Tap Settings

3) Tap Advanced Settings

4) Enter either, Installer(Default 1111), Dealer (Default 2222)

5) Tap Installation

6) Tap Devices

7) Tap Security Sensors

8) Select Either "Add Sensor" or "Auto Learn Sensor"

Auto Learn Sensor:

1) Open the cover tamper for the device or press tamper button inside the sensor when needed

2) Sensor will be displayed on screen, confirm information and continue.

Add Sensor:

1) Fill out the information needed for the sensor that is currently being programmed in

Note: GeoArm recommends using "Auto Learn Sensor" as it is much friendlier to DIY installers

Enroll PG9914 Motion Detector: 

https://www.youtube.com/watch?v=1rzgLozbTek

Enroll PG9945 Contact:

https://www.youtube.com/watch?v=lvunefTDk1Q

Enroll PG9939 Key Fob: 

https://www.youtube.com/watch?v=WF-86cNkS3I

Enroll Power G Sensor:

https://www.youtube.com/watch?v=3yZSuLTg_D4

Enroll IQ Light Bulb: 

https://www.youtube.com/watch?v=5qXwC06zesc

Enroll QS5110-840 Smoke Detector: 

https://www.youtube.com/watch?v=AEZ-FM-DsK0

Enroll IQ Carbon:

https://www.youtube.com/watch?v=omNLr-3p-9M

Program A Sensor - Auto Learn Mode

 Signing Up For Monitoring Qolsys Panel

IQ4 What's The Difference Between MHZ

Activate Z Wave Through Camera - Smart Start

Add Languages In Panel

Add A New Z Wave Device

Find Alarm Photos Settings

Allow Master Code To Access Camera - IQ4

What Does Allow Master Code To Access Security Do?

Allow Master Code To Access Sirens and Alarms

Allow Master Code To Manage Sensors

Auto Bypassing Settings

View Battery Information

Change Brightness

Change Date and Time

Change Dialer Delay

Change Engineer Reset Option

Change Exit Delay / Change Entry Delay

Change Installer Code

Change Language

Change Power Settings When On Battery Only

Change PowerG Image Capture Count

Change PowerG Siren Options

Change Siren Timeout

Change Temperature Measurement

Change Z Wave Frequency Region

Check Panel Status / Check Alarm Status / Check History

Clean Screen Mode

Configure Panel Sirens

Connect Phone With Bluetooth

Connect To Wifi / learn Into Wifi

Default Dealer Code

Default Installer Code

Default Master Code

Delete Bluetooth Device

Detect Sensor Jams / Detect RF Jam

Disable Arm Stay Counter

Disable Auto Stay

Disable Panel Tamper

Disarm Photos Settings

Edit Bluetooth Device

Edit Z Wave Devices

Enable 6 Digit User Codes

Enable Commercial Sensor and Device Names

Enable Deako Integration

Enable Exit Time Extension

Enable Keyfob Instant Arming

Enable Keyfob to Disarm System

Enable Master Code to Access Security and Arming

Enable Panel Glass Break Detector

Enable Screen Lock

Enable Secure Arming

Enable Siren Annunciation

Enable Swinger Shutdown

Enable Two Trip Verifications For Alarms

Enable Wellness Page

Enter Advanced Settings

Enter Settings

Erase All User Data

Find IMEI

Forgot Dealer Code / Forgot Installer Code

Ignoring Sensors After A Power Cycle - SIA Power Restoration

Increase Security - Require Code Before Use - EN Grade 2

Local Automation

Manage 3rd Party Connections

Manage Access Point Connection

Manage Access Point Settings

Manage Bluetooth Settings

Manage Camera Settings

Manage Energy Optimization

Manage IQ Remote Devices

Manage System Logs

Manage Users - Change Duress code

Manage Wifi Devices

Manage Z Wave Device Options / Z Wave Settings

Manage Z Wave Devices

Manage Z Wave Provisioning List

Disable Panel Camera / Enable Panel Camera

Panel Motion Detector

Power Cycle From Panel / Reboot Panel

Power Down Panel From Settings

Enroll PG9939 Key Fob

Enroll Power G Sensor

Enroll IQ Light Bulb

Enroll QS5110-840 Smoke Detector

Enroll IQ Carbon

Refuse Arming When Low Battery

Remove All Bluetooth Devices

Remove Z-Wave Device

Reset To Factory

Run a Ambient Noise Test

Run a Daughter Cards Test

Run a Dual Path Test

Run a Panel Glass Break Test

Run a Panel Test

Run a PowerG Test

Run a Scene

Run a Wifi Test

Run a Z Wave Test

Run an Input Voltage Test

Qolsys Panel 4

GeoArm Support Center