Two report channels are used by the Lynx Plus Series to support the LRR/IP communications device and
dynamic signaling. For the primary channel the device can communicate via AlarmNet GSM/IP or Cellular
communications devices. Secondary phone is not affected by dynamic signaling scheme. Two programming
options are used to define dynamic signaling behavior. Field ✻55 is used to enable/disable the LRR/IP
communications device and allows it to supervise the communications module. The two-digit option
programmed in Field ✻77 defines how dynamic signaling will function. The Dynamic signaling options are
shown as follows:&nbsp;

1) Enter Installer Code on the panel while disarmed (Default 4112) + 800

2) You Will now see 20 INSTALLER CODE if that was the correct installer code.

3) Press *77

View Attached Photo for help.

4) Press *99 After the screen updates to the next field to exit programming

Note: GeoArm can change the installer code upon activation

Follow Install manual for more information:&nbsp;
<a href="https://turbifycdn.com/ty/cdn/yhst-51756635596032/l3000-honeywell-lynx-plus-wireless-control-panel-installation-and-setup-guide.pdf" target="_blank">https://turbifycdn.com/ty/cdn/yhst-51756635596032/l3000-honeywell-lynx-plus-wireless-control-panel-installation-and-setup-guide.pdf</a>

Two report channels are used by the Lynx Plus Series to support the LRR/IP communications device and
dynamic signaling. For the primary channel the device can communicate via AlarmNet GSM/IP or Cellular
communications devices. Secondary phone is not affected by dynamic signaling scheme. Two programming
options are used to define dynamic signaling behavior. Field ✻55 is used to enable/disable the LRR/IP
communications device and allows it to supervise the communications module. The two-digit option
programmed in Field ✻77 defines how dynamic signaling will function. The Dynamic signaling options are
shown as follows: 

1) Enter Installer Code on the panel while disarmed (Default 4112) + 800

2) You Will now see 20 INSTALLER CODE if that was the correct installer code.

3) Press *77

View Attached Photo for help.

4) Press *99 After the screen updates to the next field to exit programming

Note: GeoArm can change the installer code upon activation

Follow Install manual for more information: 
https://turbifycdn.com/ty/cdn/yhst-51756635596032/l3000-honeywell-lynx-plus-wireless-control-panel-installation-and-setup-guide.pdf

Dynamic Signaling Delay / Dynamic Signaling Priority Field

Program New Sensor / Learn New Sensor

Updating and/or Deleting Account Number

15-Second Dialer Delay Burglary

5800PIR-RES - How to Program Interior Follower L3000

5800WAVE Wireless Sirens can the L3000 System Have

5818MNL - How to Program Delay and Manually

5834-4 - How to Program Arm Away Button

5834-4 - How to Program the Arm Stay Button

5834-4 - How to Program the Disarm Button

5834-4 - How to Program with a Panic Button

5853 - How to Program into the LYNX Plus

AC Loss Report Code

AC Restore Report Code

Alarm Bell Timeout

Alarm Restore Report Code

Arm Away Report Code

Armed System Test

Audible Exit Warning-Quick Exit

Audio Alarm Verification AAV Remote Phone Control 

AUX Function-1-Button Paging

Baby Sitter Code

Back Up Batteries

Bypass a Zone

Bypass Report Code

Bypass Zones L3000

Cancel Report Code

Change Installer Code - L3000

Change Master Code

Change RF House ID Code

Change the Entry Delay Timer

Change the Exit Delay Timer

Change the Master Volume

Change the Zone Descriptions

Change Time and Date

Change User Codes

Change Zone Description

Chime By Zone

Compatible LTE Communicators

Change Confirmation of Arming Ding 

Change Cross Zone Timer

Change Date and Time L3000

Change Daylight Savings Time Start-End Month 

Default Installer Code L3000

Disable Auto Stay Arming / Enable Auto Stay Arming

Disable Clock On Panel / Enable Clock On Panel

Download Call Back Phone Number

Enable Day Lights Savings Time / Disable Day Lights Savings Time

Enable Force Bypass - Disable Force Bypass

Enable Force Bypass / Disable Force Bypass L3000

Enable Keypad Backlight Timeout / Disable Keypad Backlight Timeout

Enable Quick Arming / Disable Quick Arming

Enable Test Mode / Disable Test Mode

Enter Programming L3000

Change Entry Delay 2

Change Entry Delay 1 

Event Log 80 Percent Full Report Code

Event Logging Options

Change Exit Delay L3000

Change Exit Delay Timer

Exit Error Report Code

False Alarm Options

First Test Report Offset

Flexible Callback 

Follow Me Reminder Phone Number

Has No display / Black Screen / Not Powering on / Keypad not powering on

How to Clear a Cover Tamper

How to Program Instant

How to Wire Panel

Install Back Up Battery / Install Battery

Install Cellular Communicator

Install Guide L3000

Documentation L3000

Lack of Usage Notification

Learn New Sensor / Add a sensor

Leave a Voice Message

Locate Mac and CRC from communicator

Low Battery Report Code

Low Battery Restore Report Code

Monitoring Options

Multi-mode E-mail notification

Number of Reports In Armed Period

Opening Report Code

PABX Access Code

Pager Characters

Panic Alarm

Periodic Test Report

Phone System Select

Power Cycle / Power Down / Turn Off and On

Power Up In Previous State

Powerline Carrier Device Programming

Powerline Carrier Device X10 House ID

Opening Report Code L3000

Program 5800PIR-RES Interior Follower

Program 5811 Delay Manually Learn Serial Number

Program 5811 Instant Auto Learn Serial Number

Program 5811 Instant Manually Learn Serial Number

Program 5816 Contact

Program 5816 Delay and Manually Learn Serial Number

Program 5816 Instant and Auto Learn Serial Number

L3000 Lynx Plus

GeoArm Support Center