1) Press Gear Icon

2) Enter Master Code (Default 1111)

3) Enter Network Settings

4) Enter Access Point

1) Press Gear Icon

2) Enter Master Code (Default 1111)

3) Enter Network Settings

4) Enter Access Point

Change Access Point

Signing Up For Monitoring 2GIG Edge

What is the difference between 2GIG-EDG-NA-AA and 2GIG-EDG-NA-VA

Change AC Loss Reports

AC Restore Reports

Add User Codes / Change User Codes / Delete User Code / Change Duress Code / Add Duress Code

Add Z wave Device

Alarm Restore Reports

Change Allow Backlight Always On

Battery Replacement

Change Broadband Network Failure Causing Trouble

Broadband Network Failure Reports

View Photo History - View Old Pictures 2GIG-EDG-NA

Change Broadband Network Failure Time

Adjust Burglary Bell Cut Off Time

Bypass Restore Reports

Bypass Sensors When Arming / Enable Force Bypass / Add Sensor To Force Bypass

Change Alarm Abort Window Transmission Delay / Dial Delay Settings

Change Alarm Cancel Time

Change Alert On Disarm by Keyfob Settings

Change Camera Settings

Change Date and Time - Edge

Change Demo Video

Change Entry Delay Settings

Change Event Logs / Change Events sent to central station

Change Exit Delay Count Down

Change Installer Code 2GIG EDGE 

Change Language Settings

Change Screen Settings

Change Security Pin Length

Change Smart Home Settings

Change Swinger Shutdown Count

Change Temperature Display Units

Check Enrolled Keyfobs

Check Enrolled Keypads

Check Image Sensor / Add Image Sensor

Check Z wave Network

Compatible Communicators

Configurations Change Acknowledgment

Cross Sensor Timeout

Default Installer Code - 2GIG Edge

Default Master Code 2GIG Edge

Disable Quick Exit / Enable Quick Exit

Documents 2GIG Edge

Change Emergency Button Sound Settings

Enable siren after 2 way voice / Disable siren after 2 way voice

Enable 2 way Voice / Disable 2 way Voice

Enable Alarm Canceled Display / Disable Alarm canceled display

Enable All Smart Areas To Have Sounder Follows

Enable Auto Unbypass / Disable Auto Unbypass

Enable Chime / Disable Chime

Enable Cross Sensor Zones 99-100 / Disable Cross sensor Zones 99-100

Enable Exit Delay Restart / Remove Exit Delay Restart

Enable Key Fob Arm disarm confirmation / Disable Key Fob Arm disarm confirmation

Enable Key Fob zone auto bypassing / disable key fob zone auto bypassing

Enable LED Mode Control / Disable Led mode control

Enable Local Smart Home Z-Wave / Disable Local Smart Home Z-Wave

Enable Master User to access Z-Wave Setup

Enable On Board Camera / Disable On Board Camera

Enable On Board Camera Events

Enable Quick Arming / Disable Quick Arming / Change Quick Arming

Enable Quick Bypass / Disable Quick Bypass

Enroll New Sensors / Add new sensors / Learn new sensor

PIR1e Programming Motion Detector

Key2e Programming Key Fob

DW10e Programming Contact

FT6e Programming Water Leak

SMKT8e Programming Smoke Detector

Enrolling SMKT8e Heat Detector

Enrolling SMKT8e Freeze Detector

Enter Programming

Enter Z wave Settings

Features

Adjust Fire Bell Cutoff Time

Firmware Update

Change Force Bypass Reports

How to check enrolled zones

How To Find IMEI 2GIG Edge

How To Put System On Test

How to restore settings to default

How To View Dealer Info

Change Lack of usage Notification Time

Learn Into Wifi 2GIG Edge

Lock Defaulting Panel

Lock Smart Home To Master Code

Look At Panel History

Lowest Dial Delay Setting

Manual Bypass Reports

Change On Board Camera Settings

Open Collector output Settings

2GIG EDGE Panel Overview

Trigger a Panic Button

Change Periodic Test Timer

Power Cycle

Change Programming Mode Entry

Radio Fail Timer / Radio Modem Network Failure Timer

Radio Network Causes trouble Setting

Radio Network Failure Reports

Random AC Loss Report Time

Rediscover Z wave network

2GIG Edge

GeoArm Support Center